Branch Model: DISTRELAY
AutoCorrection Properties
To be documented.
Model Equations and/or Block Diagrams
Parameters:
| Notrip | 0 means to monitor and Trip; 1 means it will only monitor |
| Shape1 | Zone 1 Shape; 0 means a circle, lens or tomato; 1 means a rectangle; 2 means reactance distance; 3 means impedance distance |
| Shape2 | Zone 2 Shape; 0 means a circle, lens or tomato; 1 means a rectangle; 2 means reactance distance; 3 means impedance distance |
| Shape3 | Zone 3 Shape; 0 means a circle, lens or tomato; 1 means a rectangle; 2 means reactance distance; 3 means impedance distance |
| Shape4 | Zone 4 Shape; 0 means a circle, lens or tomato; 1 means a rectangle; 2 means reactance distance; 3 means impedance distance |
| TransferType | Transfer Trip Type; 0 means none; 1 Direct Underreaching Transfer Trip (DUTT); 2 Permissive Overreaching Transfer Trip (POTT); 3 Permissive Underreaching Transfer Trip (PUTT); 4 means Directional Comparison Blocking (DCB) |
| UseLoadEncroach | Use Load Encroachment Model |
| NumDirect | Number of Trips which are Direct. 0 is treated as 1, otherwise this is the number of trip branches which are considered a direct trip. Others are considered as transfer trip. |
| RecloseWithFault | Reclose With Fault Not Cleared? 1 means a YES (Default), 0 means NO |
| DirectTrip | Direct trip, cycles |
| DirectReclose | Direct reclose, cycles |
| TransferTrip | Transfer trip, cycles |
| TransferReclose | Transfer reclose, cycles |
| Angle1 | Zone 1 Angle, Degrees |
| Wt1 | Zone 1 Wt, Primary Ohms |
| Rr1 | Zone 1 Rr, Primary Ohms |
| InternalAng1 | Zone 1 InternalAng, Degrees |
| Rb1 | Zone 1 Rb, Primary Ohms |
| T1 | Zone 1 Time, seconds |
| IThres1 | Zone 1 IThres, Line Amps |
| Angle2 | Zone 2 Angle, Degrees |
| Wt2 | Zone 2 Wt, Primary Ohms |
| Rr2 | Zone 2 Rr, Primary Ohms |
| InternalAng2 | Zone 2 InternalAng, Degrees |
| Rb2 | Zone 2 Rb, Primary Ohms |
| T2 | Zone 2 Time, seconds |
| IThres2 | Zone 2 IThres, Line Amps |
| Angle3 | Zone 3 Angle, Degrees |
| Wt3 | Zone 3 Wt, Primary Ohms |
| Rr3 | Zone 3 Rr, Primary Ohms |
| InternalAng3 | Zone 3 InternalAng, Degrees |
| Rb3 | Zone 3 Rb, Primary Ohms |
| T3 | Zone 3 Time, seconds |
| IThres3 | Zone 3 IThres, Line Amps |
| Angle4 | Zone 4 Angle, Degrees |
| Wt4 | Zone 4 Wt, Primary Ohms |
| Rr4 | Zone 4 Rr, Primary Ohms |
| InternalAng4 | Zone 4 InternalAng, Degrees |
| Rb4 | Zone 4 Rb, Primary Ohms |
| T4 | Zone 4 Time, seconds |
| IThres4 | Zone 4 IThres, Line Amps |
| BlindType0 | 1st Blind type, 0, +1, -1, +2, or -2 |
| BlindInt0 | 1st Blind intercept, Primary Ohms |
| BlindRot0 | 1st Blind rotation, Degrees |
| BlindType1 | 2nd Blind type, 0, +1, -1, +2, or -2 |
| BlindInt1 | 2nd Blind intercept, Primary Ohms |
| BlindRot1 | 2nd Blind rotation, Degrees |
| BlindType2 | 3rd Blind type, 0, +1, -1, +2, or -2 |
| BlindInt2 | 3rd Blind intercept, Primary Ohms |
| BlindRot2 | 3rd Blind rotation, Degrees |
| BlindType3 | 4th Blind type, 0, +1, -1, +2, or -2 |
| BlindInt3 | 4th Blind intercept, Primary Ohms |
| BlindRot3 | 4th Blind rotation, Degrees |
| FarRelayEnd | Far Relay is at the Other End; 0 (Default) means it will look for the Far Relay Device to be at a different end from this device location end plus the Device id; 1 means it will look for Far Relay Device and only will look for the Device id (The device end will not matter) |